Showing all 17 results

Show sidebar

Copper Headjoint Fitting Strips

Finally a reliable, reversible solution for temporary and long term headjoint fitting! Our new copper headjoint strips are used for fitting headjoints to flutes when the headjoint is too small to fit securely. Peel-and-stick adhesive backing.

$6.65 Add to cart

Drill Rod Assortment

1 each of our 17 most popular sizes. 36″ rods are shipped as 2 x 18″ pieces.

$116.00 Add to cart

Drill Rod

0-1 drill rod is perfect for making replacement rods (screws, axles) and various tools in the shop. Priced per 3 foot lengths. Shipped as 2 x 18″ pieces.

$5.70$14.00 Select options

Slow-cure 30 Minute Epoxy 4.5 Oz.

Slow-Cure 30 Minute Epoxy has the highest strength of our epoxies.

$13.99 Add to cart

Quick-Cure 5 Minute Epoxy 4.5 Oz.

Quick-Cure 5 Minute Epoxy cures to a slightly flexible consistency.

$16.35 Add to cart

JLS High E Facilitators – Delrin

Our Valentino High E Facilitator (a.k.a. “donut” or poor man’s split-E) is an option that may help tame the high E on the flute. This note can be problematic, as it tends to respond stubbornly and sound stuffy and out of tune. Our easy-to-install, pre-made high-E facilitators can be glued into the lower G tone hole with 5-minute epoxy. Available in white delrin.

For installation directions, see the description below.

Pearl Powder 1/2 oz.

This product can be mixed with any clear finish or color for that shimmering pearl look, and can be mixed with epoxy to make your own finger button pearls, sax key pearls, guitar inlays, you name it!

$8.25 Add to cart

JLS Silicone Work Mat

Our JLS Silicone Work Mat is an excellent and versatile mat for soldering, glue-up, and general bench work.

The silicone is heat resistant and isn’t damaged by splashed solder.  Our Work Mat is easy to wipe clean and has a surface tension that holds an instrument securely.

As a bonus, dried adhesives (hot-melt, epoxy, CA) are easily removed with a fingernail.

Measures approximately 20″ x 23″.

$49.25 Add to cart

Clarinet Tenon Sleeve – Hard Rubber

This part is intended to fit over a clarinet’s center or barrel tenon joint (after the tenon joint has been turned down on a lathe).

It can be adhered to the tenon joint with epoxy.

$20.00 Add to cart

Hard Rubber Clarinet Tone Hole Inserts

Clarinet Tone Hole Inserts are great for repairing cracks that run through the tone hole of a clarinet. They are made out of hard rubber.

Use an end mill to create a flat surface for the Clarinet Tone Hole Insert. Then use epoxy to secure it.

If using a mill, you should use an end mill that’s the same diameter as the tone hole.

If using a drill press, you may lose about .010” accuracy, so you may need to get an even smaller end mill.

Both Clarinet Tone Hole Inserts have a .436″ O.D.

$13.25$13.50 Select options

JLS Flute Pad Stabilizer Assortment

138 stabilizers assorted by need. Comes organized and labeled in our plastic bin box.

$96.00 Add to cart

JLS Flute Pad Stabilizer – Brass

JLS Flute Pad Stabilizers, when properly installed, create a flat and stable base on which to pad. This leads to better and more reliable padding and adjustment of the flute.

JLS Flute Pad Stabilizer – Plastic

JLS Flute Pad Stabilizers, when properly installed, create a flat and stable base on which to pad. This leads to better and more reliable padding and adjustment of the flute.

Carbon Fibre Ribbon – 12 Ft.

Graphite banding is the sure way to guarantee that a crack will stay closed permanently.

Click for PDF Instructions

$16.00 Add to cart